LCDA 630 Series AC Servo Motor Driver

Product Description

LICHUAN® warmly welcome you to wholesale LCDA 630 Series AC Servo Motor Driver from our factory. Our products are CE certified and currently have a large amount of factory inventory. We will provide you with good service and factory discounted prices

220V 380V AC LCDA630 servo motor driver specifications

Regarding environmental conditions, please be sure to comply with the specifications set by our company. If you need to use it outside the specified environmental conditions, please consult our company in advance.
① Install in a place that will not be directly exposed to sunlight.
② The driver must be installed in the control box
③ Install it in a place where it will not be immersed by water or oil (cutting oil, oil mist) and without moisture.
④ Keep away from corrosive atmospheres such as explosive and flammable gas, sulfide gas, chlorinated gas, ammonia, etc., acid/alkali and salt.
⑤ A place that will not be disturbed by dust, iron powder, cutting powder, etc.
⑥ Keep away from high temperature places, places with continuous vibration and excessive shock.

1.Support 23bit encoder .23bit encoder AC servo motor.
2. Match for AC servo motor rated power from 3KW-37KW.

Chapter 2 Electrical Specifications

Item				Specifications
		vibration		5.8m/s2(0 .6G)below 10～60Hz(Can not be used continuously at resonance frequen cy)
	Insulation withstand voltage			Basic-FG between AC1500V 1min
	Control way			Three-phase PWM converter sine wave drive
	Encoder feedback			1:Provincial line 2500 line 2:17bit (after adding a battery, it can be used as a multi-turn absolute encoder)
	Control signal		Input	9 inputs (DC24V optocoupler isolation) switch according to the control mode function
			Output	5 output (DC24V optocoupler isolation, open collector output) switch according to the control mode function
	Pulse signal		Input	2 inputs (optocoupler isolation, RS-422 differential, open collector output)
			Output	4 outputs(A/B/Z phase RS-422 differential;Z phase open collector output)
	Communic ation function		RS232	For PC communication(for "Servostudio" connection)
			RS-485	For upper remote control communication (1:n)
			CAN	CANOPEN bus communication
	Regeneration function			Optional regenerative resistor, external regenerative resistor. Pay attention to modify internal parameters
	Dynamic brake			YES
	Control model			6 control modes: speed control, position control, torque control, torque/speed control, speed/position control, torque/position, torque/speed/position hybrid control
	Control input			Alarm reset, proportional action switching, zero fixed function enable, forward drive prohibited, reverse drive prohibited, external torque limit for forward rotation, external torque limit for reverse rotation, forward jog, reverse jog, forward Reset switch, reverse reset switch, origin switch, emergency stop, servo enable, gain switch
	Control output			Servo ready, motor rotating, zero speed signal, speed reached, position reached, positioning approach signal, torque limit, speed limit, brake output, warning, servo failure, alarm code (3-digit output)
	P 0	P u	Maximum command pulse frequency	Differential input: high-speed maximum 4Mpps, pulse width cannot be less than 0.125μs The maximum low speed is 500Kpps, and the pulse width cannot be less than lus Open collector: maximum 200Kpps, pulse width cannot be less than 2.5us

Combination of drive model and motor

Control output			Servo ready, motor rotating, zero speed signal, speed reached, position reached, positioning approach signal, torque limit, speed limit, brake output, warning, servo failure, alarm code (3-digit output)
P 0 S T 0 n C 0 n t r 0 1	P u L S e N P u t	Maximum command pulse frequency	Differential input: high-speed maximum 4Mpps, pulse width cannot be less than 0.125μs The maximum low speed is 500Kpps, and the pulse width cannot be less than lus Open collector: maximum 200Kpps, pulse width cannot be less than 2.5μs
		Input pulse signal form	Differential input; open collector
		Input pulse signal method	Pulse + direction, right angle phase difference (A phase +B phase), CW+CCW pulse
		Command pulse division/multiplication (Electronic gear ratio setting)	0.1048576<B/A <419430.4
		Command filter	Smoothing filter, FIR filter
	P ul se 0 ut P ut	Output pulse form	Phase A, Phase B: Differential output Z phase: differential output or open collector output
		Frequency division ratio	Arbitrary frequency division
		Ou tpu t pulse function	Encoder position pulse and position pulse command (can be set)
S p e e d C 0	Control input		Servo ON, alarm reset, speed command reverse, zero speed clamp, internal command selection input 1, internal command selection input 2, internal command selection input 3, internal command selection input 4, forward rotation external torque limit input, reverse rotation External torque limit input, emergency stop
S p e e d C 0	Control output		Alarm status, servo preparation, brake release, torque limit output, speed limit output speed reached, speed consistent, motor rotation output, zero-speed signal output