Intelligent 2 Phase Hybrid Motor Driver

Product Description

Wholesale Newest Intelligent 2 Phase Hybrid Motor Driver made in China. LICHUAN® is Intelligent 2 Phase Hybrid Motor Driver manufacturer and supplier in China.

Product Introduction

LC2280D is a new generation digital two-phase step drive developed based on the 32-bit DSP technology. The control signal plug is modified based on those for old models, so the operation is easier. A dialing switch allowing 1Mhz and 200Hz pulse input mode switching is added to the drive, effectively solving the interference problem happened sometimes and making the product application more popular. This drive combines more advanced algorithms, greatly reducing the noise caused by the motor during operation and making the motor run more stably and reliably. This LC2280D driver match for Nema42 hybrid stepper motor, pls check driver manual if u wanna know more information.

Product specifications

➢ Voltage input range: AC110V～280V
➢ Max. peak current: 7.0A
➢ Subdivision range: 400～60000ppr
➢ Pulse form: pulse + direction (dual-pulse not supported)
➢ Pulse response frequency: 0～1MHz
➢ When the pulse stops for 1.5s, the coil current will be automatically reduced to half of the set value
➢ Provided with overvoltage, overcurrent and motor phase loss protection functions, etc.

Operating environment and parameters

● Voltage input range:AC110V～280V
● Maximum peak current:7.0A
● Subdivision range:400～60000ppr
● Pulse form:pulse +direction (do not support double pulse)
● Impulse response frequency: 0～1MHz
● The pulse stops for 1.5S, and the coil current isautomatically reduced to half of the set value
● With over-voltage,over-current; motorlack ofequal protectionfunction

Environmental parameters

● Storage temperature:-20° ℃~65 ℃ · Operating temperature:0 ℃~50 ℃
● Operating humidity: 40～90%RH(non-condensing)
● Vibration frequency: less than 0.5G(4.9m/s2)10Hz~ 55Hz(discontinuous operation)
● Avoid dust, oil stains, corrosive gases, places with too much humidity and too strong vibration, and prohibit flammable gas and conductive dust

Drive function description

Drive function	Instructions
Microstep subdivision setting	The number of micro-step subdivisions of the driver is set by four DIP switches SW5~SW8.There are 16 micro-step subdivisions in total. When the user sets subdivisions, the driver should be stopped first.For score setting, please follow the driver panel instructions.
Output current setting	The output current of the driver is set by four DIP switches SW1~SW4, and there are 16 output currents in total. For the specific output current setting, please refer to the driver panel description.
Automatic half -flow function	About 0.3 seconds after the pulse train stops, the current is automatically reduced by 50%(the actual value is 55%), and the heat generation is theoretically reduced by 65%, which reduces the heat generation of the motor and the driver and improves the reliability
Signal interface	PUL+ and PUL- are the positive and negative ends of the control pulse signal; DIR+ and DIR-are the positive and negative ends of the direction signal: ENA+ and ENA- are the positive and negative ends of the enable signal, ALM+ and ALM- are the alarm signal output, RDY+ and RDY- are ready for signal output.
Motor interface	A+ and A- are connected to the positive and negative ends of the A-phase winding of the stepping motor; B+ and B- are connected to the positive and negative ends of the B-phase winding of the stepping motor. When the A and B two-phase windings are exchanged, the direction of the motor can be reversed.
Power connector	Powered by AC power, working input voltage range: 110V～280VAC
Indicator light	The drive has two indicator lights, red and green. The green light is the powerindicator, which is always on when the drive is powered on; the red light is the fault indicator, which is always on when there is an overvoltage or overcurrent fault. After the fault is cleared, the red light goes out. When the drive fails, only a power cycle and re-enable can clear the fault.
Installation Notes	The external dimensions of the driver are: 203 x 147 x 78mm, and the mounting hole distance is 193mm.It can be installed horizontally or vertically (vertical installation is recommended). When installing, it should be close to the metal cabinet to facilitate heat dissipation.

Parameter setting

The LC2722D driver uses a ten-bit DIP switch to set the subdivision precision, dynamic current, filtering and pulse frequency, which are described in detail as follows:

Working current setting

Current	SW1	SW2	SW3	SW4
1.2	off	off	off	off
1.5	off	off	off	on
2.0	off	off	on	off
2.3	off	off	on	on
2.5	off	on	off	off
3.0	off	on	off	on
3.2	off	on	on	off
3.6	off	on	on	on
4.0	on	off	off	off
4.5	on	off	off	on
5.0	on	off	on	off
5.3	on	off	on	on
5.8	on	on	off	off
6.2	on	on	off	on
6.5	on	on	on	off
7.0	on	on	on	on

Installation size (unit: mm)

Microstep subdivision setting

Subdivision	SW5	SW6	SW7	SW8
400	on	on	on	on
500	on	on	on	off
600	on	on	off	on
800	on	on	off	off
1000	on	off	on	on
1200	on	off	on	off
2000	on	off	off	on
3000	on	off	off	off
4000	off	on	on	on
5000	off	on	on	off
6000	off	on	off	on
10000	off	on	off	off
8000	off	off	on	on
20000	off	off	on	off
30000	off	off	off	on
60000	off	off	off	off